Mastic waterproofing bitumen-latex MG-6 Ecobit DSTU B V.2.7-108-2001 20 kg, Dnipropetrovsk region.

Mastic waterproofing bitumen-latex MG-6 Ecobit DSTU B V.2.7-108-2001
To create a waterproofing layer on mineral, wooden and metal bases (for example, foundations and plinths of buildings, wooden fences and metal structures made of steel and cast iron) to protect them from atmospheric influences.

Bitumen-latex waterproofing mastic MG-6 Ecobit DSTU B V.2.7-108-2001

To create a waterproofing layer on mineral, wooden and metal bases (for example, foundations and plinths of buildings, wooden fences and metal structures made of steel and cast iron) to protect them from atmospheric influences.

Appointment
To create a waterproofing layer on mineral, wooden and metal bases (for example, foundations and plinths of buildings, wooden fences and metal structures made of steel and cast iron) to protect them from atmospheric influences.

Basic consumer properties
• easily applied to various bases
• moisturizes well and penetrates into the pores of absorbent bases
• has good adhesion to various materials
• quick drying
• forms a film with waterproofing properties after drying.
• compatible with freshly mixed cement, gypsum and lime bases

Appearance and composition
Black paste, which is a bitumen emulsion with highly elastic polymer dispersions andspecial additives.

Technical characteristics at t° = 20 °C and relative air humidity 60%

Estimated consumption for a single-layer coating, kg/m? 0.1-0.5
The force of uniform separation, MPa, is not less than 0.5
Elongation of the dried film of the waterproofing composition with a thickness of 2 mm during application, % not less than 400
Drying time of the film of the waterproofing composition with a thickness of 0.5 mm during application, no more than 1 hour

Instructions for use
When carrying out furnishing and waterproofing works, it is necessary to follow SniP 3.04.01 87 "Insulating and finishing coatings" and the original instructions.
External conditions during the works
The optimal temperature is 18-25 °C(//tractor-service.com)
Optimal humidity 60-70%
Permissible temperature is 8-35 °C

Preparation of the base
Before use, the base must be cleaned of dust, dirt, whitewash, salts, rust, oil and grease stains.

Application procedure
Before using the mastic, it is necessary to mix it until it is averaged. Then, depending on the tool used for application, it is allowed to dilute it with water, but not more than 30% and mix thoroughly for averaging. As a result of dilution with water, a waterproofing composition is obtained, ready to be applied with a brush, similar to paint.
During storage of the composition diluted with water, liquid separation is possible. This composition must be thoroughly mixed before use (for example, using a drill with a nozzle) until homogeneity is achieved. To avoid delamination, it is recommended to use the composition within one hour from the moment the mastic is diluted.

It is recommended to apply the composition in one or two layers (in the case of maximum dilution of the mastic with water, it is necessary to apply at least 2 layers), preventing the formation of gaps, streaks and puddles.
The optimal thickness of applying the composition in one pass to obtain a continuous waterproofing film is: on dense bases — 0.05-0.1 mm (approximate consumption 0.05-0.1 kg/m?; drying time at 20 °C — about 10-15 minutes); on porous bases - up to 0.5 mm (approximate consumption up to 0.5 kg/m2; drying time at 20 °C - no more than 1 hour). In the case of an increase in the thickness of the applied layer above the optimum, as well as in high humidity and lower temperatures, the drying time of the applied film increases.

Applying a second layer of waterproofing composition should be done after the treated surface has dried.
After the composition dries, the surface of the film has residual stickiness, which decreases in the future. If it is necessary to obtain a non-sticky surface, as well as to protect the surface from adverse effects (for example, on a repaired roof), it is possible to sprinkle the freshly applied waterproofing composition with a powder material, for example, sand (similar to sprinkling on soroid).
Wash working tools with soap and water. If necessary, use a solvent for bituminous materials.

Conditions and term of storage
The warranty period of storage is 12 months, provided that it is stored and transported in the manufacturer's unopened package at a temperature of plus 5-35 °C.
Safety measures
During the application of the waterproofing composition, it is necessary to protect the eyes and skin. The material that got on the skin should be washed off with warm water and soap, and in the absence of these measures, washed off with white spirit, and then the skin should be washed with warm water and soap and smeared with cream; in case of contact with the eyes and mucous membranes, it is necessary to wash them thoroughly with warm water and, if necessary, consult a doctor.

Waste disposal
Remains of unused waterproofing composition should be mixed with sand and allowed to harden. The hardened material is construction waste.

Packaging and packing
Polymer bucket 5 kg;
Polymer flask 40 kg.

Manufacturer's service and guarantees
The manufacturer guarantees the compliance of the product with the technical specifications and the specified technical characteristics, during the implementation of the rules of transportation, storage and use given in this description. The manufacturer is not responsible for improper use of the product, as well as for its use for other purposes and conditions not provided for in this description.
The manufacturer provides professional consultations on the use of materials