Mastic waterproofing bitumen-latex MG-5 Ecobit DSTU B V.2.7-108-2001 20 kg, Dnipropetrovsk region.

Mastic waterproofing bitumen-latex MG-5 Ecobit DSTU B V.2.7-108-2001
For sealing inter-panel joints in the walls of residential and industrial buildings, joints of horizontal and vertical structural elements, as well as for plastering, painted with water-dispersion colors, waterproofing of vertical surfaces of foundations, plinths, tunnels, technical wells, inter-floor ceilings, retaining walls. For waterproofing of roofs, balconies, terraces, walls and floors in basements, bathrooms and toilets.

Bitumen-latex waterproofing mastic MG-5 Ecobit DSTU B V.2.7-108-2001

For sealing inter-panel joints in the walls of residential and industrial buildings, joints of horizontal and vertical structural elements, as well as for plastering, painted with water-dispersion colors, waterproofing of vertical surfaces of foundations, plinths, tunnels, technical wells, inter-floor ceilings, retaining walls. For waterproofing of roofs, balconies, terraces, walls and floors in basements, bathrooms and toilets.

Appointment

For sealing inter-panel joints in the walls of residential and industrial buildings, joints of horizontal and vertical structural elements, as well as for plastering, painted with water-dispersion colors, waterproofing of vertical surfaces of foundations, plinths, tunnels, technical wells, inter-floor ceilings, retaining walls. For waterproofing of roofs, balconies, terraces, walls and floors in basements, bathrooms and toilets.

Main consumer properties

• elastic
• the mastic film is resistant to cold brittleness at temperatures down to minus 20 °C
• environmentally friendly
• waterproof and steamproof
• colored with water-dispersion colors
• behind the dried reinforced layer of mastic, you can plaster, lay a screed, putty, paint and glue ceramic tiles.

Appearance and composition

Light yellow mass with the consistency of petroleum jelly. It is a water emulsion of natural and synthetic polymers.

Instructions for use

During finishing works, it is necessary to be guided by SniP 3.04.01-87 "Insulating and decorative coverings", DBN V.2.6-14-95 "Constructions of buildings and structures. Covering of buildings and structures" and the original instructions of the original instructions of the original instructions.

Preparation of the base(//tractor-service.com)

The base must be flat, free of loosely fixed particles, dust, dirt, rust, and not contain water on the surface. Defects in building structures are recommended to be repaired with repair plasters: RSh-1 (repair of plaster layers); RSh-2 (repair of the surface of supporting and fencing structures); RSh-3 (floor repair). The protruding parts of the armature must first be cleaned of rust. All types of absorbent bases must be strengthened with a primer to increase the strength of adhesion to the waterproofing layer: ГД-2 (for porous bases) or ГД-4 (for low-porous bases).

Application procedure

The mastic is completely ready for use. Apply mastic with a brush, spatula or roller. The consistency of the mastic makes it possible to use a syringe gun for its application. To obtain reduced viscosity, mastic is diluted with water, but not more than 1: 2 (water: mastic). It is strictly forbidden to dilute mastic with organic solvents in order to avoid loss of waterproofing properties.

1. For waterproofing foundations, plinths, tunnels, technical wells, retaining walls, floor slabs and inter-panel joints, mastic is applied in layers. A layer of mastic 0.3 mm thick (corresponding to a consumption of mastic of approximately 0.35 kg/m2) under normal conditions (20 °C and 60-70% humidity) dries in no less than 60 minutes, and a one-time applied layer 1 mm thick takes 3 days. Therefore, to accelerate the drying of the waterproofing layer, the recommended total thickness of the waterproofing film is approximately 1 mm, formed by three layers of 0.3 mm. During the layer-by-layer application of mastic, each subsequent layer must be applied after the previous one has dried, and subsequent layers must be applied in cross directions. During the drying time, the applied layer must be protected from moisture and mechanical impact to acquire good waterproofing properties.

2. To increase the mechanical strength of the mastic film, especially in places where moisture may accumulate, it is recommended to apply several 1 mm layers as described above, reinforcing each layer with a non-woven reinforcing material. The reinforcing material is laid directly behind the fresh layer of MG-5, sinking it with a roller or spatula. After the reinforced mastic dries, it can be covered with acrylic (colored) paint VD-AK-11 or acrylic varnish VD AK 111, pigmented with aluminum powder, treated with plaster РШ-1, РШ-2 (wall) and РШ-3 (floor), puttying, gluing ceramic tiles with КС-1, КС-5 or КК-1 glue. Different types of decoration can be applied behind a layer of plaster or putty (VD-AK-11 painting or different types of decorative plasters). It is recommended to carry out the described decoration no earlier than 7 days after applying the mastic. To increase the adhesion of plasters to the waterproofing layer, it is recommended to pre-treat it with adhesive primer GA-1. It is possible to paint the mastic itself with water-dispersion coloring pastes. At the same time, high-brightness pigments, such as pigment titanium dioxide, ocher or surik, in addition to the decorative effect, protect the mastic film from ultraviolet light.

Conditions and term of storage

The warranty period of storage is 12 months, provided that it is stored and transported in the manufacturer's unopened package at a temperature of plus 5-35 °C.

Safety measures

Avoid contact with eyes. In case of contact with the skin, wash with cold water and soap, if necessary, with organic solvents (for example, white spirit).

Waste disposal

The remains of dried mastic are environmentally harmless and are ordinary construction waste.

Packaging and packaging Polymeric buckets 1; 5 and 11 kg;
Polymer flask 40 kg.

Manufacturer's service and guarantees

The manufacturer guarantees the compliance of the product with the technical specifications and the specified technical characteristics, during the implementation of the rules of transportation, storage and use given in this description. The manufacturer is not responsible for improper use of the product, as well as for its use for other purposes and conditions not provided for in this description. The manufacturer provides professional consultations on the use of materials.